收藏本站
TNY263-268
the appropriate current limit. At high loads, when the EN/UV
pin is high (less than 240 μ A out of the pin), a switching cycle
with the full current limit occurs. At lighter loads, when EN/UV
reduced even further (Figure 9). Only a small percentage of
cycles will occur to satisfy the power consumption of the
power supply.
is high, a switching cycle with a reduced current limit occurs.
The response time of the TinySwitch-II ON/OFF control
At near maximum load, TinySwitch-II will conduct during
nearly all of its clock cycles (Figure 6). At slightly lower load, it
will “skip” additional cycles in order to maintain voltage
regulation at the power supply output (Figure 7). At medium
loads, cycles will be skipped and the current limit will be
reduced (Figure 8). At very light loads, the current limit will be
V
EN
CLOCK
scheme is very fast compared to normal PWM control. This
provides tight regulation and excellent transient response.
Power Up/Down
The TinySwitch-II requires only a 0.1 μ F capacitor on the
BYPASS pin. Because of its small size, the time to charge this
capacitor is kept to an absolute minimum, typically 0.6 ms.
Due to the fast nature of the ON/OFF feedback, there is no
overshoot at the power supply output. When an external
resistor (2 M Ω ) is connected from the positive DC input to the
EN/UV pin, the power MOSFET switching will be delayed
during power-up until the DC line voltage exceeds the
threshold (100 V). Figures 10 and 11 show the power-up timing
waveform of TinySwitch-II in applications with and without an
D
MAX
external resistor (2 M Ω ) connected to the EN/UV pin.
During power-down, when an external resistor is used, the
power MOSFET will switch for 50 ms after the output loses
I DRAIN
V DRAIN
PI-2749-050301
regulation. The power MOSFET will then remain off without
any glitches since the undervoltage function prohibits restart
when the line voltage is low.
Figure 12 illustrates a typical power-down timing waveform of
TinySwitch-II. Figure 13 illustrates a very slow power-down
timing waveform of TinySwitch-II as in standby applications.
The external resistor (2 M Ω ) is connected to the EN/UV pin in
this case to prevent unwanted restarts.
The TinySwitch-II does not require a bias winding to provide
power to the chip, because it draws the power directly from
Figure 6.
V
EN
CLOCK
TinySwitch-II Operation at Near Maximum Loading.
the DRAIN pin (see Functional Description above). This has
V
EN
CLOCK
D
MAX
D
MAX
I DRAIN
V DRAIN
PI-2667-090700
I DRAIN
V DRAIN
PI-2377-091100
Figure 7.
TinySwitch-II Operation at Moderately Heavy Loading.
Figure 8.
TinySwitch-II Operation at Medium Loading.
5
www.powerint.com
Rev. H 02/09
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
DAK-91 DESIGN ACCELERATOR KIT III SWTCH
DAL3W3P300G30LF CONN DSUB PLUG 3W3 T/H GOLD
DAL3W3S300G30LF CONN DSUB RCPT 3W3 T/H GOLD
DAL7W2P300G30LF CONN DSUB PLUG 7W2 T/H GOLD
DAL7W2P300G40LF CONN DSUB PLUG 7W2 T/H GOLD
DAL7W2P500G30LF CONN DSUB PLUG 7W2 T/H RA GOLD
DAL7W2S500G30LF CONN DSUB RCPT 7W2 T/H R/A GOLD
DAL7W2SA00LF DSUB POWER STB 7W2 SOCK
相关代理商/技术参数
DAK1575MS50T 制造商:TOKO 制造商全称:TOKO, Inc 功能描述:GPS DIELECTRIC PATCH ANTENNA
DAK159 制造商:Amphenol Corporation 功能描述:DAK159 - Bulk
DAK-15P 制造商:ITT Interconnect Solutions 功能描述:DAK-15P - Bulk
DAK15PF179 制造商:ITT 功能描述:DSUB 15 M WW2 G ZINC
DAK-15P-F179 制造商:ITT Interconnect Solutions 功能描述:DAK-15P-F179 - Bulk
DAK15PF179A 制造商:ITT 功能描述:DSUB 15 M SOD .154 MH WW ZINC
DAK15S 制造商:ITT 功能描述:DSUB 15 F SOD G ZINC 制造商:ITT Interconnect Solutions 功能描述:DSUB 15 F SOD G ZINC
DAK-15S 制造商:ITT Interconnect Solutions 功能描述:DAK-15S - Bulk